İsonem Liquid Marble – Countertop and Floor Coating

TECHNICAL SPECIFICATIONS

• Density (A Component, 25°C, g/mL): 1.10 ± 0.10

• pH (25°C): Not applicable

• Viscosity (A Component, 25°C, mPa·s): 1500 – 3500

• Solid Content: Not applicable

• Water Vapor Transmission (kg/m²·h⁰·⁵): < 0.1 (CLASS W3)

• Adhesion Strength (Pull-Off Test, N/mm²): ≥ 1.0 without traffic load; ≥ 2.0 with traffic load (rigid systems)

• Water Vapor Permeability (m): 5 ≤ SD ≤ 50 (CLASS II)

• Touch Dry Time: 8 – 10 hours

• Full Cure Time: 7 days

• Pot Life (23°C): 30 – 40 minutes

• Solvent: Organic

• Fire Classification: C fl S1

• Color: Special color options from the Liquid Marble color chart

APPLICATION AREAS

• Suitable for interior common areas such as showrooms, offices, homes, and shopping malls.

• Preferred as a decorative and durable floor coating in stores and commercial spaces.

• Can be applied on various surfaces including ceramic, concrete, marble, mosaic, and steel.

• Safe for use in interior spaces of laboratories and the food, chemical, and pharmaceutical industries.

• Designed exclusively for indoor applications; not suitable for outdoor use.

Surface Preparation – ISONEM Liquid Marble

• The surfaces to be coated must be free of all oil, dirt, dust, and debris, and must be clean and dry.

• For concrete and raw wooden surfaces, apply a primer using ISONEM EP PRIMER before applying Liquid Marble.

• For marble countertops, sand the surface with a sanding stone; Liquid Marble can then be applied directly without primer.

Mixing Instructions

• ISONEM Liquid Marble is supplied in ready-to-use sets according to the application ratio.

• Only prepare the amount of mixture needed for immediate use, keeping in mind the pot life.

• Materials should be at a temperature of 15–25°C.

• Mix component A mechanically at 300–400 rpm for 3–4 minutes, ensuring no air bubbles form.

• Then add component B completely into component A, ensuring all material is incorporated.

• Mix A + B for at least 3 minutes until a homogeneous mixture is obtained.

• The prepared mixture should be used within 30–40 minutes.

Application Method

• Spread the mixture over the surface using a brush or roller.

• If a thicker layer is desired, apply a second coat after the first layer has surface-dried.

• To enhance the marble effect and decorative appearance, tools such as a sponge roller, epoxy roller, or butterfly roller can be used 1–2 hours after application (during semi-dry stage).

• Initial hard curing occurs in 18–24 hours, while full curing and maximum chemical/mechanical resistance are achieved within 7 days.

Consumption / Coverage – ISONEM Liquid Marble

Consumption:

• 0.6 – 1.0 kg/m²

Coverage Area:

• 5 kg set: 5 – 8 m²

• 2.5 kg set: 2.5 – 4 m²

• 1 kg set: 1.5 – 2 m²

• 0.5 kg set: 0.5 – 1 m²

Color:

• Available in the color options shown in the Color Chart.

Packaging:

• 500 g set: A Component 320 g, B Component 180 g

• 1 kg set: A Component 640 g, B Component 360 g

• 2.5 kg set: A Component 1.6 kg, B Component 0.9 kg

• 5 kg set: A Component 3.2 kg, B Component 1.8 kg

Storage:

• Storage temperature: 5 – 35 °C

• Shelf life: 24 months in original, unopened, undamaged packaging

• Storage conditions: Keep in a dry, cool place away from heat and fire; always keep packaging tightly closed

Equipment Cleaning:

• All tools and equipment should be cleaned immediately after use with cellulose thinner.

Health & Safety:

• For safe use, storage, and disposal, always refer to the latest Safety Data Sheet (MSDS).

• Physical, ecological, toxicological, and other safety information is provided in the MSDS.